WOHLER Enable monitoring from up to a 64ch Danteâą Input. Hardware card with software activation key.
Description
Enable monitoring from up to a 64ch Danteâą Input in iAM Series products.
Installing a Wohler unit with the Dante hardware option into an existing and functioning Dante network is virtually plug and play. The iAM Series rear panel AoIP jack supports 1Gb/s and 100Mb/s Ethernet devices in Dante Audio over IP network configurations. Channel source selections are made by choosing Input Type âAoIPâ in the Configuration-Configure Presets page regardless of which AoIP option is installed. The iAM-series unit is set up at the Wohler factory to be used as a slave rather than a master within the Dante network. Other devices or software, such as a Dante Controller, are expected to be responsible for most device configurations and all audio routing.
The daughter card can be installed in the iAM Series products listed below:
-
IAM-MIX8
-
IAM-MIX16
-
IAM-AUDIO-1
-
IAM-AUDIO-2
- IAM-VIDEO-2
Â
Dante64 Capable Unit |
Option Part# |
Description |
iAM-12G-SDI |
829164 |
Adds primary and secondary RJ-45 ports for hitless/2022-7 support (for Dante and 2110-30 signals). Includes OPT-MADI/ANLG/TOS option card (829168). |
iAM-VIDEO-2-MPEG |
829078 |
Primary RJ-45 port. |
iAM-AUDIO-1 iAM-AUDIO-2 |
829078 |
Primary RJ-45 port. |
iAM-MIX8 iAM-MIX16 |
829078 |
Primary RJ-45 port. |
iVAM1-1 iVAM1-3 iVAM2-2 |
829171 |
Adds primary and secondary RJ-45 ports for hitless/2022-7 support (for Dante and 2110-30 signals). Adds a Gigabit SFP cage allowing multi-mode and single-mode network SFPâs for AoIP Signals + optical TOSLINK input. |
Spécifications
- Brand
- Wohler
- Produit
- OPT-DANTE
- Product Category
- Speaker Accessories
- Type
- Software
WOHLER Enable monitoring from up to a 64ch Danteâą Input. Hardware card with software activation key.
Description
Enable monitoring from up to a 64ch Danteâą Input in iAM Series products.
Installing a Wohler unit with the Dante hardware option into an existing and functioning Dante network is virtually plug and play. The iAM Series rear panel AoIP jack supports 1Gb/s and 100Mb/s Ethernet devices in Dante Audio over IP network configurations. Channel source selections are made by choosing Input Type âAoIPâ in the Configuration-Configure Presets page regardless of which AoIP option is installed. The iAM-series unit is set up at the Wohler factory to be used as a slave rather than a master within the Dante network. Other devices or software, such as a Dante Controller, are expected to be responsible for most device configurations and all audio routing.
The daughter card can be installed in the iAM Series products listed below:
-
IAM-MIX8
-
IAM-MIX16
-
IAM-AUDIO-1
-
IAM-AUDIO-2
- IAM-VIDEO-2
Â
Dante64 Capable Unit |
Option Part# |
Description |
iAM-12G-SDI |
829164 |
Adds primary and secondary RJ-45 ports for hitless/2022-7 support (for Dante and 2110-30 signals). Includes OPT-MADI/ANLG/TOS option card (829168). |
iAM-VIDEO-2-MPEG |
829078 |
Primary RJ-45 port. |
iAM-AUDIO-1 iAM-AUDIO-2 |
829078 |
Primary RJ-45 port. |
iAM-MIX8 iAM-MIX16 |
829078 |
Primary RJ-45 port. |
iVAM1-1 iVAM1-3 iVAM2-2 |
829171 |
Adds primary and secondary RJ-45 ports for hitless/2022-7 support (for Dante and 2110-30 signals). Adds a Gigabit SFP cage allowing multi-mode and single-mode network SFPâs for AoIP Signals + optical TOSLINK input. |
Spécifications
- Brand
- Wohler
- Produit
- OPT-DANTE
- Product Category
- Speaker Accessories
- Type
- Software